Product Details:
Payment & Shipping Terms:
|
Material: | Natural Rubber | Usage: | Mining |
---|---|---|---|
Fuel: | Diesel Or Electric | Duty Type: | Heavy Duty |
Transmission Type: | CV/ZVZ/DCZ/CR | Impeller: | 5 Closed Vans |
High Light: | abrasive slurry pump,horizontal slurry pump |
6 / 4 R Wear-Resisting Rubber Lined Centrifugal Slurry Pump For Fine Particle
Main introduction of slurry pump
The slurry pump is a single-stage single-suction, cantilever, horizontal centrifugal slurry pump. This type of pump has a thick bearing and is equipped with a heavy-duty bracket, so it is suitable for conveying strong abrasion, high concentration slurry or low concentration high lift slurry. It can be used in multiple stages in series within the range of the pump's large allowable working pressure. The pump can also be used to transport a corrosive slurry.
The slurry pump has a replaceable rubber lining and the impeller is made of rubber. The shaft seal can be a packing seal or a centrifugal seal. The pump's discharge port can be installed at a different angle from 45°C and rotated at eight different angles.
Model meaning
6 / 4 E - R
6------------Suction diameter(Inch)
4------------Discharge diameter(Inch)
E-----------Support type
-------- Pump Model
R-----------Natural Rubber
Specifications
Pump Model | 6 / 4 E - R |
Allowable Max.Power | 120 kw |
Capacity | 144 - 324 m³/h |
Head | 12 - 45 m |
Speed | 800 - 1350 r/min |
Meax.Eff. | 65 % |
NPSH | 3 - 5 m |
Impeller Diameter | 365 mm |
Typical Applications:
Ash Handling
Cyclone Feeds
Pulp and Paper
Abrasive Slurries
Coal Preparation
Mineral Processing
Aggregate Processing
Suction piping system maintenance
1) Check the pump inlet pipeline for leaks and water leakage, and the pump suction piping system is not allowed to leak.
2) Clean the foreign matter in the feed pool to ensure the particle size of the material to be transported, in line with the particle requirements that the pump can pass, so as to avoid the blockage caused by the large particle material and the fiber material entering the pump.
3) Those who use rubber pumps should pay special attention to prevent sharp solids from entering the pump, so as not to cut the rubber parts and affect the service life of the pump.
Construction Design
Shaft Seal Module Design
Performance table
MODEL | ALLOWABLE MATING | MATERIAL | CLEAN WATER PERFORANCE | IMPELLER | |||||||
MAX.POWER | LINER | IMPELLER | Q Capacity | H Head | Speed | Max. Eff. | NPSH | VANES NO. | IMPELLER DIA | ||
(KW) | m3/h | L/s | (m) | n(r/min) | (%) | (m) | (mm) | ||||
1.5/B- | 15 | M | M | 12.6-28.8 | 3.5-8 | 6-68 | 1200-3800 | 40 | 2--4 | 5 | 152 |
RU | RU | 10.8-25.2 | 3--7 | 7-52 | 1400-3400 | 30 | 3 | ||||
1/1.5B- | 15 | M | M | 16.2-34.2 | 4.5-9.5 | 25-92 | 1400-2200 | 20 | 2-5.5 | 5 | 330 |
2/1.5B- | 15 | M | M | 32.4-72 | 9--20 | 6-58 | 1200-3200 | 45 | 3.5-8 | 5 | 184 |
RU | RU | 25.2-54 | 7--15 | 5.5--41 | 1000-2600 | 50 | 2.5-5 | 5 | 178 | ||
3/2C- | 30 | M | M | 39.6-86.4 | 11--24 | 12-64 | 1300-2700 | 55 | 4--6 | 5 | 214 |
RU | RU | 36-75.6 | 10--21 | 13-46 | 1300-2300 | 60 | 2--4 | 5 | 213 | ||
3/2D-HH | 60 | M | M | 68.4-136.8 | 19-38 | 25-87 | 850-1400 | 47 | 3-7.5 | 5 | 457 |
4/3C- | 30 | M | M | 86.4-198 | 24-55 | 9-52 | 1000-2200 | 71 | 4--6 | 5 | 245 |
RU | RU | 79.2-180 | 22-50 | 5-34.5 | 800-1800 | 59 | 3--5 | ||||
4/3E-HH | 120 | M | M | 126-252 | 35-70 | 12-97 | 600-1400 | 50 | 2--5 | 5 | 508 |
6/D- | 60 | M | M | 162-360 | 40-100 | 12-56 | 800-1550 | 65 | 5--8 | 5 | 365 |
RU | RU | 144-324 | 40-90 | 12-45 | 800-1350 | 65 | 3--5 | 5 | 365 | ||
6/4S-HH | 560 | M | M | 324-720 | 90-200 | 30-118 | 600-1000 | 64 | 3--8 | 5 | 711 |
6S-HH | 560 | M | M | 468-1008 | 130-280 | 20-94 | 500-1000 | 65 | 4--12 | 5 | 711 |
8/6E- | 300 | M | M | 360-828 | 100-230 | 10-61 | 500-1140 | 72 | 2--9 | 5 | 510 |
RU | RU | 324-720 | 90-200 | 7-49 | 400-1000 | 65 | 5--10 | 5 | 510 | ||
10/8E-M | 120 | M | M | 666-1440 | 185-400 | 14-60 | 600-1100 | 73 | 4--10 | 5 | 549 |
10/8ST- | 560 | M | M | 612-1368 | 170-380 | 11-61 | 400-850 | 71 | 4--10 | 5 | 686 |
RU | RU | 540-1118 | 150-330 | 12-50 | 400-750 | 75 | 4--12 | ||||
12/10ST- | 560 | M | M | 936-1980 | 260-550 | 7-68 | 300-800 | 82 | 6 | 5 | 762 |
RU | RU | 720-1620 | 200-450 | 7-45 | 300-650 | 80 | 2.5-7.5 | ||||
14/12ST- | 560 | M | M | 1260-2772 | 350-770 | 13-63 | 300-600 | 77 | 3--08 | 5 | 965 |
RU | RU | 1152-2520 | 320-700 | 13-44 | 300-500 | 79 | 3--10 | ||||
16/14TU- | 1200 | M | M | 1368-3060 | 380-850 | 11-63 | 250-550 | 79 | 4--10 | 5 | 1067 |
20/18TU- | 1200 | M | M | 2520-5400 | 700-1500 | 13-57 | 200-400 | 85 | 5--10 | 5 | 1370 |
Tel: 86-- 031180809622
Fax: 86--031168050656