Product Details:
Payment & Shipping Terms:
|
| Brand Name: | Shiza | Pump Shaft Position: | Horizontal Pump |
|---|---|---|---|
| Rubber Lining: | R33 R08 | Impeller Type: | Open Type |
| Pressure: | Middle Pressure | Structure: | Single-stage Pump |
| High Light: | high density solids pump,sand slurry pump |
||
Open Impeller Type Slurry Pump , Single Suction Centrifugal Pump For Tailings
Main introduction
The 3 / 2 C - slurry pump is the most popular pump model among rubber lined pump models.Pump 3 / 2 C - is mostly used for the building industry handling ashes of building blocks.
The temperature of the solid-liquid mixture to be transported generally does not exceed 80 ° C (double-shell pump lined with glue pump does not exceed 60 ° C).The head of the rubber-lined impeller should not exceed 63m. The allowable line speed should not exceed 30m/m. Bearings are generally selected from rolling bearings and are lubricated with thin oil or grease. The operating temperature should not exceed 75 °C. The pump's transmission can be equipped with a flexible coupling, a drive belt or a fluid coupling. Couplings, V-belts and pulleys should have safety shields. For double-shell pumps with rubber inner casing, the size of solid particles in the slurry should not exceed 3 mm, and there is no sharp edge; for double-shell pumps with single-shell pump and metal inner casing, the size of solid particles in the slurry should not exceed 80% of the flow section size. The packing seal water pressure should be 35 kPa higher than the pump discharge port pressure.
Advantages
The 3/2C-R slurry pump is a single-stage single-suction, cantilever, horizontal centrifugal slurry pump. This type of pump has a thick bearing and is equipped with a heavy-duty bracket, so it is suitable for conveying strong abrasion, high concentration slurry or low concentration high lift slurry. It can be used in multiple stages in series within the maximum allowable operating pressure range of the pump. The pump can also be used to transport a corrosive slurry
Model meaning
3 / 2 C-R
3-------Suction diameter(Inch)
2-------Discharge diameter(Inch)
C-------Frame type
------Slurry pump type
R--------Natural Rubber
Typical Applications:
-Ash Handling
-Cyclone Feeds
-Pulp and Paper
-Abrasive Slurries
-Coal Preparation
-Mineral Processing
-Aggregate Processing
-Heavy Refusal Removal
Construction Design
Performance table
| MODEL | ALLOWABLE MATING | MATERIAL | CLEAN WATER PERFORANCE | IMPELLER | |||||||
| MAX.POWER | LINER | IMPELLER | Q Capacity | H Head | Speed | Max. Eff. | NPSH | VANES NO. | IMPELLER DIA | ||
| (KW) | m3/h | L/s | (m) | n(r/min) | (%) | (m) | (mm) | ||||
| 1.5/B- | 15 | M | M | 12.6-28.8 | 3.5-8 | 6-68 | 1200-3800 | 40 | 2--4 | 5 | 152 |
| RU | RU | 10.8-25.2 | 3--7 | 7-52 | 1400-3400 | 30 | 3 | ||||
| 1/1.5B- | 15 | M | M | 16.2-34.2 | 4.5-9.5 | 25-92 | 1400-2200 | 20 | 2-5.5 | 5 | 330 |
| 2/1.5B- | 15 | M | M | 32.4-72 | 9--20 | 6-58 | 1200-3200 | 45 | 3.5-8 | 5 | 184 |
| RU | RU | 25.2-54 | 7--15 | 5.5--41 | 1000-2600 | 50 | 2.5-5 | 5 | 178 | ||
| 3/2C- | 30 | M | M | 39.6-86.4 | 11--24 | 12-64 | 1300-2700 | 55 | 4--6 | 5 | 214 |
| RU | RU | 36-75.6 | 10--21 | 13-46 | 1300-2300 | 60 | 2--4 | 5 | 213 | ||
| 3/2D-HH | 60 | M | M | 68.4-136.8 | 19-38 | 25-87 | 850-1400 | 47 | 3-7.5 | 5 | 457 |
| 4/3C- | 30 | M | M | 86.4-198 | 24-55 | 9-52 | 1000-2200 | 71 | 4--6 | 5 | 245 |
| RU | RU | 79.2-180 | 22-50 | 5-34.5 | 800-1800 | 59 | 3--5 | ||||
| 4/3E-HH | 120 | M | M | 126-252 | 35-70 | 12-97 | 600-1400 | 50 | 2--5 | 5 | 508 |
| 6/D- | 60 | M | M | 162-360 | 40-100 | 12-56 | 800-1550 | 65 | 5--8 | 5 | 365 |
| RU | RU | 144-324 | 40-90 | 12-45 | 800-1350 | 65 | 3--5 | 5 | 365 | ||
| 6/4S-HH | 560 | M | M | 324-720 | 90-200 | 30-118 | 600-1000 | 64 | 3--8 | 5 | 711 |
| 6S-HH | 560 | M | M | 468-1008 | 130-280 | 20-94 | 500-1000 | 65 | 4--12 | 5 | 711 |
| 8/6E- | 300 | M | M | 360-828 | 100-230 | 10-61 | 500-1140 | 72 | 2--9 | 5 | 510 |
| RU | RU | 324-720 | 90-200 | 7-49 | 400-1000 | 65 | 5--10 | 5 | 510 | ||
| 10/8E-M | 120 | M | M | 666-1440 | 185-400 | 14-60 | 600-1100 | 73 | 4--10 | 5 | 549 |
| 10/8ST- | 560 | M | M | 612-1368 | 170-380 | 11-61 | 400-850 | 71 | 4--10 | 5 | 686 |
| RU | RU | 540-1118 | 150-330 | 12-50 | 400-750 | 75 | 4--12 | ||||
| 12/10ST- | 560 | M | M | 936-1980 | 260-550 | 7-68 | 300-800 | 82 | 6 | 5 | 762 |
| RU | RU | 720-1620 | 200-450 | 7-45 | 300-650 | 80 | 2.5-7.5 | ||||
| 14/12ST- | 560 | M | M | 1260-2772 | 350-770 | 13-63 | 300-600 | 77 | 3--08 | 5 | 965 |
| RU | RU | 1152-2520 | 320-700 | 13-44 | 300-500 | 79 | 3--10 | ||||
| 16/14TU- | 1200 | M | M | 1368-3060 | 380-850 | 11-63 | 250-550 | 79 | 4--10 | 5 | 1067 |
| 20/18TU- | 1200 | M | M | 2520-5400 | 700-1500 | 13-57 | 200-400 | 85 | 5--10 | 5 | 1370 |
Shaft Seal Module Design
Tel: 86-- 031180809622
Fax: 86--031168050656
