Payment & Shipping Terms:
|Material:||Chrome Alloy A05||Outlet Dia.:||200mm|
|Impeller:||5 Vanes Closed||Stage:||Single Stage|
|Application:||Mine,mineral Processing,Power， Coal， Chemical Industry||Voltage:||380V|
The ZGB type slurry pump is a horizontal, single stage, single suction, cantilever centrifugal slurry pump. The pump has the characteristics of reasonable structure, high efficiency, reliable operation and convenient maintenance and repair. It can be widely used in electric power, metallurgy, mining, coal, building materials, chemical and other industrial sectors to transport slurry containing corrosive solid particles.
Multiple stages can be used in series within the allowable working pressure range. The pump allows a maximum working pressure of no more than 3.6Mpa.
The ZGB type high Chrome horizontal centrifugal slurry pump usual has a higher head. The 200ZGB is available in three different impeller sizes, with different impeller sizes for different effects. Simply put, the larger the impeller, the higher the head flow, the harder it is to drive, and the need for a more powerful motor. Conversely, the smaller the impeller, the lower the head flow, but the smaller the motor can be driven.
200-------------Discharge Diameter (mm)
B---------------- Series Code
P-----------------Multi-stage pumps (3-4stage)
200ZGB Performance Chart
Ni acid slurry
The ZGB slurry pump has the same structure except for the pump head part (including the front and rear pump casings, the volute casing, the front and rear guard plates, the impeller, etc.), and the rest of the structure is similar. The same series of transmission parts are used, and the pump head part and the shaft seal part are pressed below. And the transmission part, respectively, describes its structural characteristics.
1, ZGB slurry pump shaft seal part: shaft seal has three forms, the auxiliary impeller shaft seal and packing shaft seal, mechanical seal.
(1) Mechanical seal: For the condition that is not suitable for the above two shaft seals, mechanical seal is adopted to reduce the number of maintenance of the shaft seal part.
(2) Packing shaft seal: The packing shaft seal structure is simple, the maintenance is convenient, and the shaft seal water is needed. For the working condition which is not suitable for the shaft seal of the auxiliary impeller and the working condition for pumping, the packing shaft seal can be used.
(3) Sub-impeller shaft seal: Single-stage pump or multi-stage series third-stage pump when the positive pressure of the pump inlet is not more than 10% of the pump outlet pressure value, the auxiliary impeller shaft seal can be used, and the auxiliary impeller shaft seal has no Dilute the slurry, the sealing effect is good and so on.
2, ZGB slurry pump pump head part: ZGB series slurry pump is a double pump shell structure, namely the front pump casing, the rear pump casing and the replaceable over-current part (including impeller, volute, front guard, Rearguard). The front and rear pump casings are made of gray cast iron or ductile iron according to the working pressure. They are vertically opened and bolted. The rear pump casing has a stop and bolts connected to the bracket. The discharge port of the slurry pump can be installed at eight angles. The front and rear covers of the impeller are equipped with back blades to reduce leakage and improve pump life and efficiency. The inlets of all types of pumps are horizontal, and the pump rotates clockwise as seen from the transmission direction.
3. Transmission part: ZGB slurry pump adopts the same series of transmissions, including bracket and bearing assembly. The pump shaft has large diameter, good rigidity, short cantilever, and will not bend and vibrate under severe working conditions. The bearing adopts single row cone. Roller bearing and deep groove ball bearing can be combined to withstand the maximum axial and radial load of the pump. The bearing is lubricated with thin oil. The end of the bearing body has a sealed end cap, which can effectively prevent the slurry and other dirt from entering the bearing. ZGB slag The slurry pump is provided with two hose joints in the bearing body, which can be connected with the water source to cool the bearing chamber, so it can work under high ambient temperature to ensure the safe operation of the bearing and has a high life.
Selection & Performance Chart
Contact Person: Zhang