Payment & Shipping Terms:
|Pump Material:||High Chrome A05||Theory:||Horizontal Impeller Pump|
|Structure:||Single Casing||Hardness:||HRC 58-62|
|Feature:||Single Casing||Impeller Dia.:||378mm|
6 / 4 D - G Dredging Sand Gravel Pump , Large Capacity Sand Pump
G series gravel pumps are mainly used for continuous conveying of strong abrasive materials that are too large for general slurry pumps to be transported, such as dredger dredging, river or seabed large particle sand mining, mining and metal smelting blasting. Wait.
G, GH series sand pumps are horizontal, single pump shell centrifugal pumps, of which GH type is a high lift gravel pump.
G, GH series gravel pump adopts a single pump shell structure with a sideband of the cassette, and the overflow passage is wide. Its flow-through parts are made of hard nickel, high chromium and other wear-resistant materials. The discharge direction of the pump can be anywhere in 360°, which has the advantages of convenient installation, good cavitation performance and abrasion resistance.
6 / 4 D - G
36 - 250 m³/h
5 - 52 m
600 - 1400 r/min
2.5 - 3.5 m
Type meaning for dredge pump
6 / 4 D-G(H)
6----------------Suction Diameter (inch )
4----------------Discharge Diameter (inch)
H----------------Gravel Pump High Head
Expeller seal: the shaft seal type of the pump mainly has a packing seal and a counter impeller seal. The auxiliary impeller seal uses the pressure seal generated by the impeller and the auxiliary impeller in series, and is generally used in the case of press-in ore feeding, but the ore pressure value is given. Not more than 10% of the pump outlet pressure value. This type of seal can be used without shaft seal water (by the oil cup on the pump body to regularly add grease), without diluting the slurry; however, it will increase the power consumption (generally about 5% of the rated power).
Packing seal: It is a common type of shaft seal. It is suitable for various working conditions. It can be matched with special materials such as PTFE filler and graphite filler. It can be used under corrosive or high temperature conditions. It has the advantages of simple structure and convenient maintenance. However, it is necessary to add shaft sealing water, and sufficient water pressure and water volume should be ensured. The shaft sealing water pressure is 35 kPa (0.35 kg/cm2) of the pump outlet pressure, and the shaft sealing water quantity depends on the size of the bracket.
G(H) gravel pump material list for parts:
|Part Name||Material||Specification||HRC||Application||OEM Code|
|Bowl, door, back liner & impeller||Metal||AB27: 23%-30% chrome white iron||≥56||Used for higher wear condition with pH between 5 and 12||A05|
|AB15: 14%-18% chrome white iron||≥59||Used for higher wear condition||A07|
|AB29: 27%-29% chrome white iron||43||Used for lower pH condition especially for FGD. It also can be used for low-sour condition and desulfuriation installation with pH not less than 4||A49|
|AB33: 33%-37% chrome white iron||It can transport oxygenated slurry with pH not be less than 1 such as phospor-plaster, nitric acid, vil, phosphate etc.||A33|
|Expeller & expeller ring||Metal||B27: 23%-30% chrome white iron||≥56||Used for higher wear condition with pH between 5 and 12||A05|
|Stuffing Box||Metal||AB27: 23%-30% chrome white iron||≥56||Used for higher wear condition with pH between 5 and 12||A05|
|Door clamp plate, bearing house & base||Metal||Grey iron||G01|
|Shaft sleeve, lantern ring/resctrictor, neck ring, gland bolt||Stainless steel||4Cr13||C21|
|Joint rings & seals||Rubber||Butyl||S21|
|Pump Model||Allowable||Clear Water Performance|
|Max. Power||Capacity Q||Head||Speed||Max.Eff.||Impeller. Dia. (mm)|
Selection & Performance Chart
Contact Person: Zhang